based on concentric disk mapping.
Concentric disk mapping was already present, but not used everywhere.
Now `sample_cos_hemisphere()`, `sample_uniform_hemisphere()`, and
`sample_uniform_cone()` use concentric disk mapping.
This changes the noise in many test images.
Pull Request: https://projects.blender.org/blender/blender/pulls/109774
The spotlight is now treated as a sphere instead of a view-aligned disk.
The implementation remains almost identical to that of a point light,
except for the spotlight attenuation and spot blend. There is no
attenuation inside the sphere. Ref #108505
Other changes include:
## Sampling
Instead of sampling the disk area, the new implementation samples either
the cone of the visible portion on the sphere or the spread cone, based
on which cone has a smaller solid angle. This reduces noise when the
spotlight has a large radius and a small spread angle.
| Before | After |
| -- | -- |
||
## Texture
Spot light can now project texture using UV coordinates.
<video src="/attachments/6db989d2-7a3c-4b41-9340-f5690d48c4fb"
title="spot_light_texture.mp4" controls></video>
## Normalization
Previously, the normalization factor for the spotlight was \(\pi r^2\),
the area of a disk. This factor has been adjusted to \(4\pi r^2\) to
account for the surface area of a sphere. This change also affects point
light since they share the same kernel type.
## Versioning
Some pipeline uses the `Normal` socket of the Texture Coordinate node for
projection, because `ls->Ng` was set to the incoming direction at the
current shading point. Now that `ls->Ng` corresponds to the normal
direction of a point on the sphere (except when the radius is zero),
we replace these nodes with a combination of the Geometry shader node
and the Vector Transform node, which gives the same result as before.
Example file see https://archive.blender.org/developer/T93676
Pull Request: https://projects.blender.org/blender/blender/pulls/109329
for energy preservation and better compatibility with other renderes. Ref: #108505
Point light now behaves the same as a spherical mesh light with the same overall energy (scaling from emission strength to power is \(4\pi^2R^2\)).
# Cycles
## Comparison
| Mesh Light | This patch | Previous behavior |
| -------- | -------- | -------- |
|  |  |  |
The behavior stays the same when `radius = 0`.
| This patch | Previous behavior |
| -------- | -------- |
|  |  |
No obvious performance change observed.
## Sampling
When shading point lies outside the sphere, sample the spanned solid angle uniformly.
When shading point lies inside the sphere, sample spherical direction uniformly when inside volume or the surface is transmissive, otherwise sample cosine-weighted upper hemisphere.
## Light Tree
When shading point lies outside the sphere, treat as a disk light spanning the same solid angle.
When shading point lies inside the sphere, it behaves like a background light, with estimated outgoing radiance
\[L_o=\int f_aL_i\cos\theta_i\mathrm{d}\omega_i=\int f_a\frac{E}{\pi r^2}\cos\theta_i\mathrm{d}\omega_i\approx f_a \frac{E}{r^2}\],
with \(f_a\) being the BSDF and \(E\) `measure.energy` in `light_tree.cpp`.
The importance calculation for `LIGHT_POINT` is
\[L_o=f_a E\cos\theta_i\frac{\cos\theta}{d^2}\].
Consider `min_importance = 0` because maximal incidence angle is \(\pi\), we could substitute \(d^2\) with \(\frac{r^2}{2}\) so the averaged outgoing radiance is \(f_a \frac{E}{r^2}\).
This only holds for non-transmissive surface, but should be fine to use in volume.
# EEVEE
When shading point lies outside the sphere, the sphere light is equivalent to a disk light spanning the same solid angle. The sine of the new half-angle is the tangent of the previous half-angle.
When shading point lies inside the sphere, integrating over the cosine-weighted hemisphere gives 1.0.
## Comparison with Cycles
The plane is diffuse, the blue sphere has specular component.
| Before | |After ||
|---|--|--|--|
|Cycles|EEVEE|Cycles|EEVEE|
|||||
Pull Request: https://projects.blender.org/blender/blender/pulls/108506
The original names were `...update_position()`, but no update in
position is performed in these functions, rather, the entries in
`LightSample` are updated. Also make clear that the functions are used
by MNEE.
Uses a light tree to more effectively sample scenes with many lights. This can
significantly reduce noise, at the cost of a somewhat longer render time per
sample.
Light tree sampling is enabled by default. It can be disabled in the Sampling >
Lights panel. Scenes using light clamping or ray visibility tricks may render
different as these are biased techniques that depend on the sampling strategy.
The implementation is currently disabled on AMD HIP. This is planned to be fixed
before the release.
Implementation by Jeffrey Liu, Weizhen Huang, Alaska and Brecht Van Lommel.
Ref T77889
* Split light types into own files, move light type specific code from
light tree and MNEE.
* Move flat light distribution code into own kernel file and host side
building function, in preparation of light tree addition. Add light/sample.h
as main entry point to kernel light sampling.
* Better separate calculation of pdf for selecting a light, and pdf for
sampling a point on the light. The selection pdf is now also stored in
LightSampling for MNEE to correctly recalculate the full pdf when the
shading position changes but the point on the light remains fixed.
* Improvement to kernel light storage, using packed_float3, better variable
names, etc.
Includes contributions by Brecht Van Lommel and Weizhen Huang.
Ref T77889
