It was impossible for drivers to use shape key properties, modifiers
generate a new mesh. After mesh evaluation the shape keys are no longer
necessary, and because of this the `key` pointer was not copied. As
drivers work on evaluated data, however, they do need this `key`
pointer.
This commit makes the `key` pointer available in evaluated meshes, but
this is somewhat dangerous. There was an explicit reason why the key on
result was kept at null pointer: to have the evaluated mesh in a
consistent state. Assigning this pointer makes it potentially
inconsistent, as the evaluated mesh and the original shape key may have
different topologies.
Reviewed By: sergey
Differential Revision: https://developer.blender.org/D7785
The preview of points was only done when the edge is wire.
Now the preview of points is done when the edge is not connected to any
quad.
Also to avoid edge slide in this case, all new vertices created in this
specific case are not selected.
Differential Revision: https://developer.blender.org/D7457
This addresses warnings from Clang-Tidy's `readability-else-after-return`
rule. This should be the final commit of the series of commits that
addresses this particular rule.
No functional changes.
This replaces header include guards with `#pragma once`.
A couple of include guards are not removed yet (e.g. `__RNA_TYPES_H__`),
because they are used in other places.
This patch has been generated by P1561 followed by `make format`.
Differential Revision: https://developer.blender.org/D8466
This matches the change that was done to the bevel modifier so that the
interface for the modifier, the active tool, and the operator are consistent.
This commit extends the refactor to the bmesh implementation too, so
that the parameters in the implementation don't stray too far from what
is exposed.
Tests are adjusted and still pass.
Internally UV selection considered close UV's to be connected.
While this could be convenient in some cases,
it complicates logic for more advanced selection operations that
need to check when UV's should be considered part of the same vertex
since simple threshold checks would give different results depending
on the order of UV's tested.
Users must now run "Merge by Distance" instead of relying
on this selection threshold.
Support custom-data correction based on surrounding geometry for all
transformation modes of the mesh transform operators.
The is the same logic used in Vert and Edge Slide.
In order not to change the current default behavior,
this property does not affect Vert and Edge Slide modes.
This will allow the easier addition of a constant radius mode in the
future and some changes in the UI to mirror the recent similar change
from "Only Vertices" to the "Affect" enum.
This mode is like Percent, but measures absolute distance along
adjacent edges instead of a percentage.
So, for example, if you use this mode with 2 segments and profile=1,
you will see the length that the bevel moves along unbeveled edges
between beveled ones will match the value specified.
Many users seem to expect this behavior, even though it means the
bevel width is uneven, so this option is for them.
Custom Loop Normals are normally encoded relative to the default
normals, similar to normal maps, allowing them to naturally follow
mesh deformations. Changes to mesh topology however often result
in nonsensical effects that are not desired.
The Remove Doubles operation especially (now known as Merge By
Distance) is intended as a purely topological operation, and
definitely should not change the vector of the custom normals.
This patch implements that behavior by converting the relative
encoding into an absolute vector layer for the duration of the
operation. It also modifies other Merge types in this way for
consistency, the Rip operator as their inverse counterpart;
and also Delete, Dissolve, Connect Path and Knife operators
as other examples more related to topology than shape.
On the technical side, this ports mesh_normals_loop_custom_set
to BMesh, and then uses a temporary Custom Data layer to store
the normals as vectors for the duration of the above mentioned
operations. When the normals are converted back to custom data,
the caller can choose whether to mark edges as sharp to preserve
distinct normals, or just average them instead. All but Remove
Doubles choose to average for now.
Differential Revision: https://developer.blender.org/D4994
This resolves a performance regression in 2.8x where every edit-mode
update performed an edit-mesh to mesh conversion.
Now the conversion will be lazily initialized if/when it's required.
New BKE_mesh_wrapper_* functions abstract over mesh data access.
Currently only edit-mesh and regular meshes are supported.
In the future sub-surface meshes may be supported too.
The `BM_mesh_bm_to_me()` function copies shape keys from the BMesh to
the Mesh. However, it tries to copy the same number of shape keys as are
defined on the target mesh. Since the target mesh does not necessarily
have the same number of shape keys as the BMesh, this would crash if the
target Mesh has more.
Found while performing some tests for {D7785}.
Differential Revision: https://developer.blender.org/D7818
Reviewed by: brecht
Surrounding includes with an 'extern "C"' block is not necessary anymore.
Also that made it harder to add any C++ code to some headers, or include headers
that have "optional" C++ code like `MEM_guardedalloc.h`.
I tested compilation on linux and windows (and got help from @LazyDodo).
If this still breaks compilation due to some linker error, the header containing
the symbol in question is probably missing an 'extern "C"' block.
Differential Revision: https://developer.blender.org/D7653
Was flipping around the 0-1 range, now (optionally) flip around each tile.
Also added this option for BMesh bmo_mirror.
Reviewed By: campbellbarton
Maniphest Tasks: T75793
Differential Revision: https://developer.blender.org/D7460
Starting select linked failed when the selected vertex or edge
was it's self delimiting.
Support using these elements for linked select
as long as they're part of an isolated selection.
Note this only changes cases where the variable was declared inside
the for loop. To handle it outside as well is a different challenge.
Differential Revision: https://developer.blender.org/D7320
