When excluding a collection containing the active object in either
texture paint or particle edit mode, the object could not be reactivated
when the collection was re-enabled. This is because the object's mode
was left in TEXTURE_PAINT or PARTICLE_EDIT, and the activation code did
not have cases to handle these modes.
This moves the code that is run when toggling out of texture paint or
particle edit modes to functions so activation can properly toggle off
the respective interaction mode.
Mix up with imapaint.paintcursor & imapaint.paint.paint_cursor
Remove imapaint.paintcursor since it wasn't used.
Also rename paint_cursor_start_explicit() to paint_cursor_start(),
removing the existing paint_cursor_start() since it took the paint
struct from the context, a value that's known by all callers.
This caused an additional argument when exiting object modes
and many other low level functions which don't need to access context.
This simplifies fixing T77073.
between fluid types
When switching to gas, the fluids were not actually destroyed, leading to
the situation that they were then destroyed when actually switching to
liquid.
Maniphest Tasks: T77264
Differential Revision: https://developer.blender.org/D7907
Now when use selection if the selection area is inside a filled area, the stroke is selected. Before it was necessary to select the border of the stroke.
This use the latest GPUTexture change to use the sampler state to avoid
the pole issues instead of using GLSL hacks.
This should fix T73942: Eevee mipmaps not respecting border mode.
Note that this also fix some discrepencies between cycles and eevee (like
boxmapping + clip).
This bridge between the new sampler state support from GPUTexture and
draw material handling.
The Sampler State is just the one from the texture for now. No change in
logic.
Most of the time current (based on order) system works fine, but when you add
or rename (i.e. re-sort) some ID, every data/memchunk afterwards would be out
of sync and hence re-stored in memory (and reported as changed).
Now we are storing the ID's session_uuid in the memchunks, which allows to
actually always find the first memchunk for an already existing ID stored in
previous undo steps, and compare the right memory.
Note that current, based-on-order system is still used almost all of the time,
search in the new ghash is only performed for a few data-blocks (when needed at all).
Reviewed By: brecht
Maniphest Tasks: T60695
Differential Revision: https://developer.blender.org/D7877
Similar to the one allowing to deactivate DNA check, etc.
Will helps reduce verbosity when making many new properties overridable.
Note that pointer properties always remain non-overridable by default,
since basically only ID pointers should be.
Reviewed By: brecht
Maniphest Tasks: T77083
Differential Revision: https://developer.blender.org/D7906
Functionality here has become confusing over time,
this removes duplicate, similar functions, preferring to set the mode
instead of toggle, enter, exit.
Mode switching utility function behaved differently regarding undo,
'ED_object_mode_toggle' for example didn't skip the undo push
where 'ED_object_mode_set' did.
Some callers chose these functions based on the intended undo behavior,
even when toggling didn't make sense.
There was also ED_object_mode_generic_enter which was similar to
ED_object_mode_set, instead of the reverse of ED_object_mode_generic_exit.
Simplify object mode switching internals:
- Replace ED_object_mode_generic_enter with ED_object_mode_set.
- Remove ED_object_mode_toggle as nearly all callers needed to check
the current mode so toggling would set the mode argument correctly.
- Use ED_object_mode_set for the object mode switching operator
to simplify logic.
- Add ED_object_mode_set_ex which has an argument to disable undo,
needed when loading undo data needs to set the mode.
- Remove unused ED_object_mode_exit.
This was caused by an oversight in rB45dbc38a8b15. When the next operation
character is found the offset is shifted in the original string. The remaining
length has to be recalculated with that offset before shifting the remaining
characters to make room for the ")".
This cleanup use the recent changes in shader interface to allow querying
the binding location a texture should use.
This should aleviate all issue we have with texture state change recompiling
the shaders at drawtime.
All binds are now treated like persistent binds and will stick until a new
shading group bind a different shader. The only difference is that you can
still change it with a new subgroup or same shader shgroup.
Since unbinding can be heavy we only do it when using `--debug-gpu`.
