This patch automatically grays out input values which can't affect the output
currently. It works with inputs of group nodes, geometry nodes modifiers and
node tools.
To achieve this, it analyses the node tree and partially evaluates it to figure
out which group inputs are currently not linked to an output or are disabled by e.g.
some switch node.
Original proposal: https://devtalk.blender.org/t/dynamic-socket-visibility/31874
Related info in blog post:
https://code.blender.org/2023/11/geometry-nodes-workshop-november-2023/#dynamic-socket-visibility
Follow up task for designing a UI that allows hiding sockets: #132706
Limitations:
* The inferencing does not update correctly when a socket starts being
animated/driven. I haven't found a good way to invalidate the cache in a good
way reliably yet. It's only a very short term problem though. It fixes itself
after the next modification of the node tree and is only noticeable when
animating some specific sockets such as the switch node condition.
* Whether a socket is grayed out is not exposed in the Python API yet. That will
be done separately.
* Only a partial evaluation is done to determine if an input affects an output.
There should be no cases where a socket is found to be unused when it can actually
affect the output. However, there can be cases where a socket is inferenced to be used
even if it is not due to some complex condition. Depending on the exact circumstances,
this can either be improved or the condition in the node tree should be simplified.
Pull Request: https://projects.blender.org/blender/blender/pulls/132219
This uses the following accessor methods in more places in more places:
`is_group()`, `is_group_input()`, `is_group_output()`, `is_muted()`,
`is_frame()` and `is_reroute()`.
This results in simpler code and reduces the use of `bNode.type_legacy`.
Pull Request: https://projects.blender.org/blender/blender/pulls/132899
`BKE_main_ensure_invariants` was added in 1fae5fd8f6. The older
`ED_node_tree_propagate_change` was already implemented as a thin wrapper around
`BKE_main_ensure_invariants`. This patch removes the wrapper and calls the more
general function directly.
A new overload of `BKE_main_ensure_invariants` is added for the common case when
only a single data-block has been modified.
Pull Request: https://projects.blender.org/blender/blender/pulls/133048
Main goals of this refactor:
* Make it more obvious which update function should be used.
* Make it more obvious which parameters are required by using references instead
of pointers.
* Support passing in multiple modified trees instead of just a single one.
No functional changes are expected.
Pull Request: https://projects.blender.org/blender/blender/pulls/132862
The new description for `bNode.type_legacy`:
```
/**
* Legacy integer type for nodes. It does not uniquely identify a node type, only the `idname`
* does that. For example, all custom nodes use #NODE_CUSTOM but do have different idnames.
* This is mainly kept for compatibility reasons.
*
* Currently, this type is also used in many parts of Blender, but that should slowly be phased
* out by either relying on idnames, accessor methods like `node.is_reroute()`.
*
* A main benefit of this integer type over using idnames currently is that integer comparison is
* much cheaper than string comparison, especially if many idnames have the same prefix (e.g.
* "GeometryNode"). Eventually, we could introduce cheap-to-compare runtime identifier for node
* types. That could mean e.g. using `ustring` for idnames (where string comparison is just
* pointer comparison), or using a run-time generated integer that is automatically assigned when
* node types are registered.
*/
```
Pull Request: https://projects.blender.org/blender/blender/pulls/132858
The part that used the context does not seem to be necessary anymore. If the
given tree has any update tag set, the same notifiers will be sent anyway by the
`tree_changed_fn` callback.
If it turns out that we are now missing some notifier, then we have to change
the caller. It either has to call the proper `BKE_ntree_update_tag_*` function,
or create the notifier directly.
This change helps to generalize the concept of propagating changes in original
data, because the context is rarely available.
Pull Request: https://projects.blender.org/blender/blender/pulls/132810
A link is unavailable when any of its sockets are unavailable. Sometimes such
links are in a weird inbetween state between being there and not being there at
all. Generally, they should be considered to not be there, but sometimes it's
still useful if they automatically come back when toggling the availability of
sockets. We don't have a replacement for this functionality yet.
This patch changes behavior so that unavailable links are treated as not being
there at all in two places:
* When deciding whether to draw an input socket value.
* When deciding what to do when drawing from a socket (to create a link from it
or detach existing links). This is done by simply removing unavailable links
when starting to drag from a corresponding socket. This allows all of the
existing logic to stay the same.
Pull Request: https://projects.blender.org/blender/blender/pulls/132184
Instead of storing an optional in the runtime data of each node,
move the field status for the socket to an array in the node tree's
runtime data. This wasn't possible before because selecting nodes
reordered nodes which caused too much cache recomputation.
The benefit is having less geometry-nodes specific data in the
node socket runtime struct, and a slight move to a more data-
oriented storage format.
Pull Request: https://projects.blender.org/blender/blender/pulls/131822
- Gives O(1) access to string length in more cases
- Convenient string manipulation functions
- Clarify difference between "no string" and "empty string"
- Avoid the need for raw pointers in the API
- Shows which API string arguments are optional
Pull Request: https://projects.blender.org/blender/blender/pulls/131473
Use StringRefNull for all function arguments and return types.
Not a StringRef but StringRefNull since there is still large
interaction with C api so null-termination usually necessary.
If string is expected to be not only empty but also a null then
optional is used. This change depends on #130935.
Pull Request: https://projects.blender.org/blender/blender/pulls/131204
Compositor: UI: remove snapping to nodes.
Snapping nodes to other nodes behaves in a very unpredictable way, which makes most snapping options useless.
The patch removes the following:
- Snapping options `Node X`, `Node Y` and `Node XY`
- Menu `Snap Node Element`
- Menu `Snap Target`
New behavior:
- Activating `Snap` always acts as 'Snap to Grid'
Part of https://projects.blender.org/blender/blender/issues/128612
Pull Request: https://projects.blender.org/blender/blender/pulls/127667
Add a new shader specifically for node sockets rather than using the
keyframe shader.
Motivation:
1. Allow easier addition of new socket shapes
2. Simplify socket drawing by avoiding special handling of multi-inputs
3. Support multi-inputs for all socket types (diamond, square, etc.)
The new shader is tweaked to look the same to the old ones.
**Comparison**
The biggest difference is that the multi socket is now more consistent
with the other sockets.
For single sockets there can be small size differences depending on zoom
level because the old socket shader always aligned the sockets to the
pixel grid. This could cause a bit of jiggling compared to the rest of
the node when slowly zooming. Therefore I left it out of the new shader
and it now scales strictly linear with the view.
**Multi Socket Types**
While there currently is no need for (.) internally, there are a few
obvious use-cases for multi-input field (diamond) sockets like
generalized math nodes with an arbitrary number of inputs (Add,
Multiply, Minimum etc.).
Co-authored-by: Jacques Lucke <jacques@blender.org>
Pull Request: https://projects.blender.org/blender/blender/pulls/119243
NOTE: This also required some changes to Cycles code itself, who is now
directly including `BKE_image.hh` instead of declaring a few prototypes
of these functions in its `blender/utils.h` header (due to C++ functions
names mangling, this was not working anymore).
Pull Request: https://projects.blender.org/blender/blender/pulls/130174
Previously, Cycles only supported the Henyey-Greenstein phase function for volume scattering.
While HG is flexible and works for a wide range of effects, sometimes a more physically accurate
phase function may be needed for realism.
Therefore, this adds three new phase functions to the code:
Rayleigh: For particles with a size below the wavelength of light, mostly athmospheric scattering.
Fournier-Forand: For realistic underwater scattering.
Draine: Fairly specific on its own (mostly for interstellar dust), but useful for the next entry.
Mie: Approximates Mie scattering in water droplets using a mix of Draine and HG phase functions.
These phase functions can be combined using Mix nodes as usual.
Co-authored-by: Lukas Stockner <lukas@lukasstockner.de>
Pull Request: https://projects.blender.org/blender/blender/pulls/123532
This makes the input field much wider. I enabled this for most string sockets
except for a few where it is important to see the label even if the user has
inserted a string already (usually because there is more than one string input).
Pull Request: https://projects.blender.org/blender/blender/pulls/127992
This replaces the plain texture selector with a proper TemplateID,
resulting in buttons to add a new texture if none is there yet, and if
there is one, there will be the usual conveniece buttons to add a fake
user, create single user copies, ..., as well as the button to go to the
textures tab in the Properties Editor for more fine-grained control over
the texture.
Fixes#126856
Pull Request: https://projects.blender.org/blender/blender/pulls/126890
Previously, the inferencing result was only stored in the socket shape.
However, that was conflicting with experiments where the socket shape and
the field state was not related.
Use snake style naming for all the kernel nodes functions.
Omit kernel prefix in the names since of the using namespace.
Use full forms of the terms
('iter' -> 'iterator', 'ntree' -> 'node_tree', 'rem' -> 'remove', ...).
Pull Request: https://projects.blender.org/blender/blender/pulls/126416
This commit moves generated `RNA_blender.h`, `RNA_prototype.h` and
`RNA_blender_cpp.h` headers to become C++ header files.
It also removes the now useless `RNA_EXTERN_C` defines, and just
directly use the `extern` keyword. We do not need anymore `extern "C"`
declarations here.
Pull Request: https://projects.blender.org/blender/blender/pulls/124469
This adds support for attaching gizmos for input values. The goal is to make it
easier for users to set input values intuitively in the 3D viewport.
We went through multiple different possible designs until we settled on the one
implemented here. We picked it for it's flexibility and ease of use when using
geometry node assets. The core principle in the design is that **gizmos are
attached to existing input values instead of being the input value themselves**.
This actually fits the existing concept of gizmos in Blender well, but may be a
bit unintutitive in a node setup at first. The attachment is done using links in
the node editor.
The most basic usage of the node is to link a Value node to the new Linear Gizmo
node. This attaches the gizmo to the input value and allows you to change it
from the 3D view. The attachment is indicated by the gizmo icon in the sockets
which are controlled by a gizmo as well as the back-link (notice the double
link) when the gizmo is active.
The core principle makes it straight forward to control the same node setup from
the 3D view with gizmos, or by manually changing input values, or by driving the
input values procedurally.
If the input value is controlled indirectly by other inputs, it's often possible
to **automatically propagate** the gizmo to the actual input.
Backpropagation does not work for all nodes, although more nodes can be
supported over time.
This patch adds the first three gizmo nodes which cover common use cases:
* **Linear Gizmo**: Creates a gizmo that controls a float or integer value using
a linear movement of e.g. an arrow in the 3D viewport.
* **Dial Gizmo**: Creates a circular gizmo in the 3D viewport that can be
rotated to change the attached angle input.
* **Transform Gizmo**: Creates a simple gizmo for location, rotation and scale.
In the future, more built-in gizmos and potentially the ability for custom
gizmos could be added.
All gizmo nodes have a **Transform** geometry output. Using it is optional but
it is recommended when the gizmo is used to control inputs that affect a
geometry. When it is used, Blender will automatically transform the gizmos
together with the geometry that they control. To achieve this, the output should
be merged with the generated geometry using the *Join Geometry* node. The data
contained in *Transform* output is not visible geometry, but just internal
information that helps Blender to give a better user experience when using
gizmos.
The gizmo nodes have a multi-input socket. This allows **controlling multiple
values** with the same gizmo.
Only a small set of **gizmo shapes** is supported initially. It might be
extended in the future but one goal is to give the gizmos used by different node
group assets a familiar look and feel. A similar constraint exists for
**colors**. Currently, one can choose from a fixed set of colors which can be
modified in the theme settings.
The set of **visible gizmos** is determined by a multiple factors because it's
not really feasible to show all possible gizmos at all times. To see any of the
geometry nodes gizmos, the "Active Modifier" option has to be enabled in the
"Viewport Gizmos" popover. Then all gizmos are drawn for which at least one of
the following is true:
* The gizmo controls an input of the active modifier of the active object.
* The gizmo controls a value in a selected node in an open node editor.
* The gizmo controls a pinned value in an open node editor. Pinning works by
clicking the gizmo icon next to the value.
Pull Request: https://projects.blender.org/blender/blender/pulls/112677
This adds support for renaming some sockets in the node UI directly by Ctrl+Clicking
on them. This is sometimes more convenient than going to the sidebar. It affects the
Menu Switch and Bake node as well as the Simulation and Repeat zone.
Some related notes:
* The Group Input and Group Output node are not yet supported, because it currently
breaks the right-alignment on the Group Input node. I couldn't find a workaround for
this yet.
* Double-clicking on the socket name does not trigger renaming yet. This seems to
be a deeper issue in the interface code.
* The highlighting when hovering over sockets that can be renamed is very dim
making it hard to see. Alternatives like drawing a box around the label when hovering
it (like in list views) have been discussed but seem to be much more difficult to get to work.
Despite these limitations, it seems reasonable to add this already, as it shouldn't affect
anyone negatively. The nodes still look like before.
Co-authored-by: Hans Goudey <hans@blender.org>
Pull Request: https://projects.blender.org/blender/blender/pulls/121945
Previously, when dropping a node on a link with incompatible sockets, the link
would be removed. While sometimes useful in super simple setup, it is generally
useless for most work. Even worse, users might not notice that they accidentally
removed a link (this has been reported in the recent geometry nodes workshop).
This patch changes this behavior in two ways:
* A node can't be inserted onto an incompatible link anymore.
* A link will be dimmed while dragging a node over it, if it is incompatible or if
alt is pressed.
Pull Request: https://projects.blender.org/blender/blender/pulls/121975
Blender shows invalid links in red in the node editor. However, it's not always
obvious why some links don't work, especially for beginners. This patch adds
additional information for every invalid link on the node that it links to.
The following error messages are added:
* Invalid link because of missing implicit conversions.
* Link cycle in node tree.
* A link from a field to a socket that does not support fields.
* Using the same menu on multiple Menu Switch nodes.
Currently, there are some per tree-type special cases in the link validation code.
In the future, this should be moved to tree type specific callbacks.
Pull Request: https://projects.blender.org/blender/blender/pulls/121976
Move all header file into namespace.
Unnecessary namespaces was removed from implementations file.
Part of forward declarations in header was moved in the top part
of file just to do not have a lot of separate namespaces.
Pull Request: https://projects.blender.org/blender/blender/pulls/121637
